Pavel Prikhodko wrote:
>>>VU> в conf.default создан новый раздел "GENERAL CONFIGURATION CONTROLS"
>>>VU> в нем описаны два параметра - confIGNORE_BOUNCE_ERRORS_AFTER и
>>>VU> confTIMEOUT_FROZEN_AFTER, значения которых будут использованы в
>>>VU> configure в качестве значений параметров ignore_bounce_errors_after и
>>>VU> timeout_frozen_after соответственно
>>>>>>VU> в будущем скорее всего таки придется парсить содержимое
>>>VU> site/configure.general, чего до сих пор очень хотелось бы избежать
>>>>>># tail -2 ../site/conf
>>>define(`confIGNORE_BOUNCE_ERRORS_AFTER', `1d')dnl
>>>define(`confTIMEOUT_FROZEN_AFTER', `2d')dnl
>>>>>># gmake all install
>>>>>># grep ignore_bounce_errors_after ../configure
>>>#ignore_bounce_errors_after = 1d
>> VU> а ты перед этим gmake sync выполнял?
> VU> если я внес изменения в конфиги, то их синхронизировать надо
>> Блин!
>> 2004-08-03 17:06:26 H=leylak.tr.net (leylak.trnet.com) [195.155.1.5] F=<info на giritshipping.com> temporarily rejected RCPT <sergey на albatros.od.ua>: failed to expand ACL string "${if eq{$acl_m0}{yes}{${perl{dbm_save}{/var/spool/exim/db/proxycheck.db}{$sender_host_address}{openproxy}{1}}}{${perl{dbm_save}{/var/spool/exim/db/proxycheck.db}{$sender_host_address}{ok}{1}}}}": Undefined subroutine &main::dbm_save called.
перловый файл не подключился, судя по всему. или пересобрался криво.
после того, как сделаешь gmake sync all, рекомендованный в предыдущем
письме, поверь содержимое exim.pl
> # gmake sync
> rsync -avz --delete rsync://bsd.falbi.kiev.ua/exim-conf/acls/ ../acls/
> receiving file list ... done
>> wrote 91 bytes read 1344 bytes 956.67 bytes/sec
> total size is 99508 speedup is 69.34
> rsync -avz --delete rsync://bsd.falbi.kiev.ua/exim-conf/deliveries/ ../deliveries/
> receiving file list ... done
>> wrote 97 bytes read 288 bytes 256.67 bytes/sec
> total size is 26726 speedup is 69.42
> rsync -avz --delete rsync://bsd.falbi.kiev.ua/exim-conf/features/ ../features/
> receiving file list ... done
>> wrote 95 bytes read 629 bytes 482.67 bytes/sec
> total size is 60949 speedup is 84.18
> if [ -f ../m4/CHANGES ]; then \
> mv ../m4/CHANGES /tmp/exim-conf-CHANGES; \
> fi; \
> rsync -avz --delete rsync://bsd.falbi.kiev.ua/exim-conf/m4/ ../m4/ --exclude '*m4/CHANGES.bak'
> receiving file list ... done
> deleting CHANGES.bak
> ./
> CHANGES
>> wrote 128 bytes read 1369 bytes 998.00 bytes/sec
> total size is 121104 speedup is 80.90
> if [ -f /tmp/exim-conf-CHANGES ]; then \
> mv /tmp/exim-conf-CHANGES ../m4/CHANGES.bak ; \
> fi; \
> sync_perl :
> sync_perl: not found
> gmake: *** [sync_m4] Error 127
упс... лишние "; \"
итак, по итогам двух писем тебе надо сделать:
gmake sync && gmake sync all install restart
--
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Best wishes Victor Ustugov mailto:victor на corvax.kiev.ua
public GnuPG/PGP key: http://victor.corvax.kiev.ua/corvax.asc
ICQ: 77186900, 32418694 CRV2-RIPE, CRV-UANIC